Luminous NXG 850 680W 12V Pure Sine Wave Solar Hybrid IPS Inverter

  • Solar Hybrid Power Backup: Delivers clean 850VA / 680W Pure Sine Wave AC output on a single 12V battery with an in-built solar charge controller for homes and shops.

  • Intelligent Solar Optimization (iSOT): Prioritizes solar energy over grid electricity to charge the battery and run connected loads, reducing monthly electricity bills.

  • Built for Bangladesh Grid Conditions: Operates across a wide grid input window (90V–290V AC) and handles frequent load shedding across urban and semi-urban areas.

  • 3 User-Settable Priority Modes: Switch between Solar, Solar + Grid, and Grid + Solar modes alongside Tubular, Flat Plate, and VRLA/GEL battery support.

  • Comprehensive Electronic Protection: Safeguards connected devices and internal circuitry against overload, short circuit, over-temperature, low battery, and reverse feed.

Best Price Guaranteed

Description

The Luminous NXG 850 is a microprocessor-controlled 850VA (680W) 12V Pure Sine Wave Solar Hybrid IPS and Home UPS inverter with an integrated solar charge controller. Operating on a single 12V DC battery bank, it intelligently blends rooftop solar PV power and utility grid electricity to run connected AC appliances and maintain battery charge.

It is designed for homeowners, retail shopkeepers, remote workers, and small office operators who want uninterrupted power backup alongside lower monthly grid electricity consumption. Across Bangladesh—where frequent load shedding, rising utility tariffs, and wide voltage fluctuations (90V–290V) impact daily life—the Luminous NXG 850 prioritizes clean solar energy during daytime hours while providing dependable battery backup whenever grid power fails.

Key Features

  • 850VA / 680W Rated Capacity: Comfortably powers ceiling fans, LED lights, a television, Wi-Fi router, and essential office electronics within its 680W rating.

  • Pure Sine Wave Output: Produces clean, low-distortion AC power safe for sensitive electronics and inductive motors.

  • Built-In Solar Charge Controller with iSOT: Features Intelligent Solar Optimization Technique (iSOT) and Intelligent Load Sharing (ILS) to maximize solar energy utilization.

  • Single 12V Battery Architecture: Works with one 12V battery and supports Tubular, Flat Plate, and VRLA/GEL battery chemistries.

  • 3 User-Selectable Operating Modes: Choose between Solar, Solar + Grid, and Grid + Solar priority modes based on local outage frequency and tariff goals.

  • Wide Mains Input Voltage Range (90V–290V): Tolerates severe grid voltage swings without excessive battery discharge.

  • Comprehensive Safety Protections: Built-in safeguards against overload, short circuit, over-temperature, low battery, and output reverse feed.

Technical Advantages

  • Intelligent Solar & Load Sharing: Dynamically shares daytime loads between solar panels and the utility grid, reducing grid draw and extending battery backup reserve.

  • Clean Waveform for Sensitive Appliances: Pure sine wave output prevents motor hum in ceiling fans and protects power supplies in routers, laptops, and computers.

  • Configurable Charging Current: Mains charging current adapts by selected mode (0A in pure Solar mode, 15A ± 2A in Solar + Grid, and up to 20A ± 2A in Grid + Solar mode).

  • Single-Battery Cost Efficiency: Operates on a single 12V battery and supports 12V solar panels (17V–25V Voc), keeping initial system installation straightforward.

  • Clear Diagnostics & Protection: Front-panel status indicators and audible alarms simplify monitoring of solar charging, mains availability, and fault conditions.

Applications

  • Residential: Apartments, single-family homes, and village residences running ceiling fans, LED lights, televisions, and Wi-Fi routers with rooftop solar support.

  • Commercial: Retail shops, pharmacies, diagnostic sample points, and POS billing counters.

  • Industrial: Light workshop control desks, testing benches, and auxiliary lighting circuits.

  • Factory: Administrative offices, security cabins, and small monitoring stations.

  • Office: Small offices, home workstations, networking routers, and CCTV surveillance setups.

  • Project Installation: Off-grid and hybrid solar backup retrofits for classrooms, telecom repeaters, and security hubs.

Why Choose This Product?

  • Proven Brand Engineering: Manufactured by Luminous Power Technologies, a trusted name in solar and power backup systems.

  • Dual Benefit of Backup + Bill Savings: Combines a 680W pure sine wave IPS with a built-in solar charger to cut grid dependency during sunny hours.

  • Adaptable to Any Grid Schedule: Three user-selectable priority modes let you favor maximum solar savings or maximum battery readiness during heavy load shedding.

  • Local Purchase & Support: Available through loopshop.com.bd with convenient online ordering and customer support in Bangladesh.

Technical Specification Table

Specification Details
Model NXG 850 (NXG+ 850VA)
Brand Luminous
Rated Power 680 W (850 VA class)
Voltage 12V DC (Single Battery) / 230V ± 10V AC Output / Solar Voc: 17V–25V
Current Max Mains Charging Current: 15A–20A (Mode Dependent)
Frequency 50 Hz ± 0.5 Hz
Efficiency >80% (Battery Mode)
Protection Overload, Short Circuit, Over-Temperature, Low Battery, Output Reverse Feed
Dimension 32.0 x 30.2 x 13.0 cm (320 x 302 x 130 mm)
Weight 8.2 kg – 11.8 kg (Variant Dependent)
Operating Temperature 0°C to 45°C (0–95% RH Non-Condensing)
Warranty Official Manufacturer Warranty Applicable.

Features List

  • ✓ 850VA / 680W pure sine wave output on a single 12V battery

  • ✓ In-built solar charge controller with Intelligent Solar Optimization Technique (iSOT)

  • ✓ Supports up to 850Wp 12V solar PV panels (17V–25V Voc)

  • ✓ 3 user-selectable priority modes: Solar, Solar + Grid, and Grid + Solar

  • ✓ Compatible with 12V Tubular, Flat Plate, and VRLA/GEL batteries

  • ✓ Wide grid input acceptance range (90V–290V AC)

  • ✓ Overload, short-circuit, over-temperature, and low-battery protection

Benefits For Customers

  • Lowers Monthly Electricity Bills: Intelligent solar prioritization uses rooftop solar power first to charge the battery and run daytime appliances.

  • Protects Sensitive Electronics: Pure sine wave output keeps ceiling fans, routers, laptops, and LED TVs running quietly without electrical hum or resets.

  • Handles Bangladesh Voltage Fluctuations: Wide mains operating window (90V–290V) maintains reliable performance even when grid voltage drops.

  • Flexible Mode Control: Switch easily between maximum solar savings and maximum grid-backed battery reserve depending on weather and load shedding.

Installation & Maintenance Guide

Installation Requirements:

  • Install the inverter indoors on a dry, level surface or battery trolley in a well-ventilated room with at least 15 cm of clearance around cooling vents.

  • Connect a single compatible 12V battery using heavy-gauge copper battery cables with clean, tight terminal lugs.

  • Connect 12V-class solar panels (within the 17V–25V Voc and up to 850Wp limit) through a DC MCB/isolator with correct positive (+) and negative (-) polarity.

  • Configure the battery-type switch (Tubular / Flat Plate / VRLA-GEL) and operating priority mode (Solar / Solar + Grid / Grid + Solar) before powering on.

  • Connect the AC mains input to a properly earthed wall socket or MCB-protected line and wire only approved backup loads to the output.

Maintenance Tips:

  • Clean dust and bird droppings from rooftop solar panels every 2 to 4 weeks using water and a soft cloth to maintain peak solar charging efficiency.

  • Inspect battery terminals and solar DC connections every 2 to 3 months for corrosion or loose lugs and keep them clean and secure.

  • For flooded Tubular or Flat Plate batteries, check electrolyte levels monthly and top up strictly with distilled water.

  • Wipe dust from the inverter cabinet and cooling vents with a dry cloth so airflow remains unobstructed.

Safety Instructions:

  • Always verify DC polarity (+ and -) for both the 12V battery and solar PV array before making connections.

  • Never exceed the specified solar PV open-circuit voltage (Voc 17V–25V) or connect 24V high-voltage string panels to this 12V hybrid inverter.

  • Do not connect heavy high-wattage appliances such as air conditioners, geysers, electric irons, microwaves, or water pumps to the inverter output.

  • Switch off the inverter and isolate solar PV, AC mains, and battery terminals before performing any wiring work or servicing.

FAQ Section

Q: What is the price of Luminous NXG 850 in Bangladesh?

A: Prices for the Luminous NXG 850 Solar Hybrid IPS Inverter in Bangladesh generally range between BDT 11,500 and BDT 14,500 for the inverter unit alone, depending on current import pricing and stock availability. Check the top of this product page on loopshop.com.bd for the exact live price.

Q: Where can I buy Luminous NXG 850 in Bangladesh?

A: You can buy the genuine Luminous NXG 850 online in Bangladesh directly from loopshop.com.bd, with fast nationwide delivery across Dhaka, Chattogram, Sylhet, Khulna, Rajshahi, and all districts.

Q: What warranty does this product have?

A: The Luminous NXG 850 inverter unit comes with a 24-month (2-year) warranty covering manufacturing defects and internal electronic faults.

Q: Is this suitable for Bangladesh climate?

A: Yes. Rated for 0°C to 45°C ambient operation with a 90V–290V AC grid input window, it is well suited for Bangladesh’s warm weather, abundant sunlight, and frequent load-shedding conditions.

Q: How to install this product?

A: Mount or place the inverter in a ventilated indoor area, connect a single 12V battery with matching + and - polarity, wire compatible 12V solar panels (17V–25V Voc) through a DC isolator, set the battery type and operating mode switches, and connect AC input and backup load lines. Professional electrician installation is recommended.

Q: Can the Luminous NXG 850 work without solar panels at first?

A: Yes. It functions as a standard 12V Pure Sine Wave IPS/UPS using utility grid charging, and you can connect solar panels later whenever you are ready to expand.

Q: What solar panels are compatible with the NXG 850?

A: It supports 12V solar panels with an open-circuit voltage (Voc) between 17V and 25V, up to 850Wp total array capacity (wired in parallel).

Q: Are the battery and solar panels included in the price?

A: No, the listed price covers the Luminous NXG 850 solar hybrid inverter unit only. A 12V battery and solar panels are purchased separately.

Q: What battery types can be used with Luminous NXG 850?

A: It supports single 12V Tubular, Flat Plate, and VRLA/SMF/GEL batteries via a user-selectable battery type switch.

Q: Can I run a Wi-Fi router or computer on this solar IPS?

A: Yes. Its pure sine wave output and fast changeover support Wi-Fi routers, laptops, desktop computers, ceiling fans, and LED lights within the 680W rating.

Reviews

There are no reviews yet.

Be the first to review “Luminous NXG 850 680W 12V Pure Sine Wave Solar Hybrid IPS Inverter”

Your email address will not be published. Required fields are marked *

We Don't Just Sell Products, We Deliver Complete Solutions.

From planning to handover – Loop Shop is your single point MEP partner.

Expert Consultant

Get advised from our MEP Specialist

Supply & Installation

Professional installation by certified engineers

Testing & Commissioning

Ensuring system works perfectly

After Sales Support

AMC & 24/7 technical support

Have Project in Mind?

Get free and consultations and quotation for your project. 

Need Help Deciding?

Leave your number and we'll contact you with the best offer.


Notice: ob_end_flush(): Failed to send buffer of zlib output compression (0) in /home/loopshop/public_html/wp-includes/functions.php on line 5581